Selected model: Realme RMX3085 (Realme 8)
Operation: Repair
Software version: 4.2

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM23 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM23 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID =  0xA99E120B, 0x278CD1D5, 0x5C6E4A7C, 0xC8FA0070
Get Chip ID... [MT6785]
Get SOC ID... [F93900009BEB0D59D0B142A46A70F6DB697AF54BD3228FFC80215DF761CF1C52]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V9001JM-B813 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
   UFS_CID   : KM8V9001JM-B813
   UFS_FWVER : 0600
   BLOCK_SIZE: 0x0000001000 (4.00Kb)
   UFS_LU0   : 0x0000400000 (4.00Mb)
   UFS_LU1   : 0x0000400000 (4.00Mb)
   UFS_LU2   : 0x1DCB000000 (119.17Gb)
RAM INFO:
   INT_SRAM: 0x0000080000 (512.00Kb)
   EXT_RAM : 0x0200000000 (8.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(3)
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
  IMEI 1:  353********481
  IMEI 2:  353*********481
Write IMEI [NVDATA]... OK
Checking patch type... [1]
Patching partition... OK
Save patched partiton... OK
Read partitions info from phone... OK
Read security partition from phone... OK
Decrypting security data... OK
Encrypt security data... OK
Write security partition to phone... OK
Checking additional lock... [DISABLED]
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.